Picture Hang Solutions

Picture Hanging Hardware & Supplies

Sawtooth Hangers

Nailess

 

Other Pages

in this Category

Nail & Screw Sawtooth Hangers

Sawtooth Hangers Overview

Other Hardware

Categories

Picture Hooks

Picture Hangers

Picture Wire

Security Hangers

Hanging Systems

Picture Rail Hanging

Heavy-Duty Hangers

Frame Bumpers

Foamboard Hangers

Specialty Hangers

Hardwall Hooks

Push-Pin Hooks

Cleat Hangers

Mega Hardware

Specialty Picture Hooks

Summary

Pages

Home Page

Product List

Quick Order Forms

Site Map

Information

Pages

Ordering

Payment

Shipping

Bulk Pricing

Warranty

Returns

Samples

FAQ

Privacy

Security

About Us

Contact Us

Self-Attaching No-Nail Picture Hangers

Tempered Steel, Black Oxide Finish

Nailess Sawtooth Hangers are attached to the back side of a picture frame, usually placing just one at the center of the top rail, with the serrated "teeth" of the hanger facing downward. The frame is then hung on an ordinary nail in the wall by positioning the sawtooth hanger teeth over the protruding shank of the nail.

Made of tempered steel with a durable black oxide finish, each nailess sawtooth has two pronged "legs" that enable it to be attached to a wood picture frame without screws or nails. The hardened finish allows the hanger to be hammered into position without deforming.

Nailess Sawtooth Hangers install very quickly--an important advantage if you have a lot of frames to hang. Except for very hard woods like oak or ash, pilot holes are usually not necessary.

The sawtooth hangers on this page are for wood frames only. For metal frames, use this hanger instead. For conventional nail-on or screw-on type wood frame sawtooth hangers, go to this page.

Please keep in mind that nailess sawtooth hangers are intended for use on small or lightweight picture frames only.

The weak link in the sawtooth system is usually not the sawtooth hanger itself, but rather the nail driven into the wall. Ordinary nails can come loose or tear out, especially in drywall, so make sure the nail you place in the wall is tight before you hang a sawtooth frame on it. Wood paneling and similar hardwall surfaces are less of a problem as they hold nails better than drywall.

Nailess Sawtooth Hangers	Nailess Sawtooth Detail

Additional Notes

• Wall nails are not provided with sawtooth hanger orders.

• Do not use sawtooth hangers on large or heavy pictures. The Wall Buddies Hanger is a good alternative for larger pictures.

• Frames equipped with sawtooth hangers should not be hung on picture hooks. Even a small picture hook is too wide to engage sawtooth hanger teeth properly and the picture hook will be visible above the frame when the picture is hung.

• The sawtooth hangers on this page are for wood frames only. For metal frames, use our notched hanger, available here.

• For a very large heavy-duty sawtooth hanger, go to this page.

1. Lay the frame face down on a blanket or soft surface.
2. The hanger should be installed centered left-to-right on the top rail, a little down from the upper edge of the frame.
3. For HWR-3920 the serrated edge of the hanger should face down. HWR-3919 has two serrated edges and can be installed either way.
4. Use a small hammer to tap the nailess sawtooth hanger in place.
5. Take care not to break the glass on the frame, if any, when hammering in a nailess sawtooth hanger.
6. In extremely hard woods, drill small pilot holes for the legs of the hanger.
7. When properly seated, the shoulders of a nailess hanger should rest on the surface of the frame rail, leaving approximately 1/8" gap between the back of the hanger and the surface of the rail.
8. Make sure that your nail in the wall is tight and secure before using it to hang the frame. Always use a headed nail (not a brad) and position the frame on the nail so that the nail is caught firmly on the sawtooth hanger.

 

Related Pages

Nail & Screw Sawtooth Hangers • Sawtooth Hangers Overview